CGI Patio Door Installation Nationwide

CGI Patio Door Installation in Houston: What to Know First

CGI patio door installation in Houston typically runs $1,800 to $4,600 depending on the series, panel configuration, and whether the existing opening needs reframing. Most single-panel CGI slider replacements take one full day; two-panel or multi-slide projects run two to three days. We’re an independent CGI service provider, not a factory-authorized dealer, which means we quote honest prices and install to the manufacturer’s spec without the showroom markup. If you own a CGI patio door that’s binding, leaking, or just worn out, call (432) 278-2282 and we’ll give you a written price before any work starts.

Call (432) 278-2282

This page is for Houston homeowners who already own CGI doors or want a CGI door installed right the first time. Elliot Vance leads every estimate review personally.

How CGI Products Fail – and How We Fix Them

• CGI Estate Series slider track wear. The Estate line uses a reinforced aluminum track that holds up to coastal wind ratings, but Houston’s fine silt and humidity work grit into the roller channels. The symptom is a door that glides fine for two feet, then binds hard. That’s not the panel warping; it’s roller bearings grinding down until the wheel cants. We pull the panel, replace the rollers with stainless-steel sealed bearings, and clean the track channel before reinstalling. Elastomeric track sealant goes back on to keep future grit out.
• CGI Sentinel Series thermal bow. Sentinel doors carry thick impact glass, and a west-facing Houston exposure bakes the exterior side while the interior stays air-conditioned. Over years, the frame can bow a few millimeters. The door starts dragging on the latch side and the lock won’t set without lifting the handle. The factory fix is shimming at the header and jambs; we do that, then verify the reveal with a straightedge before sealing. A bow left uncorrected wears out the weatherstripping in months.
• CGI Encore Series roller sag from oversized panels. Encore panels run wide and heavy. When a previous installer hung them on builder-grade rollers, the door sags and the top corner pulls away from the weatherstripping. You’ll feel a draft at eye level before you see anything wrong. We swap in high-capacity tandem rollers rated for the panel weight, reset the panel height, and the door rides square again.
• Interlock channel warping on CGI aluminum lines. CGI’s aluminum patio doors have an interlock where the meeting stiles overlap. Houston’s clay-heavy soil shifts under slabs, and when the settling transfers into the frame, that interlock pinches or spreads. Water gets driven in by spring thunderstorms, and the first sign is a wet carpet near the door after a hard rain. We re-square the frame at the sill and header, re-bed the interlock, and replace any compressed wool pile.
• Fogged glass on CGI impact panels. CGI uses laminated glass with an interior airspace. When the edge seal fails from repeated heat cycling (Houston summers hit 95-plus for weeks), condensation forms inside the unit. The door still functions, but you can’t see through it cleanly. On patio doors, we recommend replacing the insulated glass unit rather than the whole door; it’s a two-hour job versus a full-day teardown, and it preserves your existing frame.

Our CGI Patio Door Installation Process

1. 1
   The call and the diagnostic. You describe the problem, we ask targeted questions over the phone, and we schedule a visit. Our technician walks the door, checks the reveal, the rollers, the sill, and the locking points. Elliot reviews every diagnostic before a number goes on paper.
2. 2
   Written price. You get a line-item quote covering parts and labor. It does not change at the door. If we find hidden damage, we stop and show you before we do anything.
3. 3
   Parts decision. We spec OEM rollers, weatherstripping, and hardware whenever available. For out-of-production CGI series, we use aftermarket components that match or exceed the original spec. We tell you which is which and why.
4. 4
   The install. Panels come out, frame gets checked for square and shimmed as needed, new hardware goes in, and the panel is reset to spec. Sill is leveled and sealed; the header gets a foam backer rod and elastomeric caulk on both sides. The Garrison Code means clean job site, no shortcuts, and no surprise extras.
5. 5
   Load test and walkthrough. We cycle the door at least ten times, check the lock engagement, run the full range of travel. Then we walk you through the work and hand you the written guarantee.
6. 6
   365-Day Done Right Promise. If anything we installed fails within a year, we come back at no charge. That’s in writing, not a verbal promise.

What CGI Patio Door Installation Costs in Houston

Straight replacement of a single CGI patio door panel with new rollers and weatherstripping runs $220 to $480. Full-frame CGI slider install, including tear-out, reframing, new door, and finish work, starts around $2,400 and goes to $4,600 for larger multi-panel configurations. If the slab has settled and the frame needs significant re-leveling, add $300 to $800. Glass unit replacement on a fogged CGI door falls between $450 and $950 depending on glass type and panel size. Permits are not required for a door-for-door swap in most Houston jurisdictions, but if the opening changes size, we pull them as part of the written price. Call (432) 278-2282 for a firm quote; estimates are free.

Why Houston Homeowners Call Meridian Windows and Doors Houston for CGI Work

We answer the phone. A live person picks up every hour of every day. When a patio door is off its track or leaking during a storm, you don’t want a voicemail prompt; you want a technician who knows CGI doors. Our crew works in the Heights, Spring Branch, Katy, Sugar Land, and across the greater Houston area, and we’ve seen every failure mode these doors can throw. If the repair proves uneconomical, we spec replacement doors from CGI, PGT, CWS, ES Windows, or ECO Window Systems, so the recommendation matches the job instead of whatever brand we happen to stock. Price goes on paper before the first screw turns, and the 365-Day Done Right Promise covers every installation in writing. Elliot Vance grew up learning this trade at Los Angeles Trade-Technical College and spent twenty years installing doors across the country; the crew works to his standard: measure twice, seal it right, and the window does the rest of the talking.

FAQs